Office Interiors | Interior Fit Out | Design Refurbishment | Redhill

Richaire Litimed: Office Partitionings

01737 77 11 31

sales@richaire.co.uk

Est. 1972

 

Richaire Timber Partition System

 

Richaire Timber Partitions are from the Avanti Legno range which is an award winning design that uses solid, kiln dried hardwood. The Timber is finished with stains and/or polishes to enhance its natural beauty. Anyone who has worked with wood well knows it actually improves with age, developing a deep patina of natural earth tones. The system incorporates demountable, hardwood trimmed partitions of nominal 75 mm or 100 mm widths.

 

Panels comprised of glass or gypsum boards, pre-decorated or otherwise, are assembled to a sub-frame of steel floor and ceiling channels and vertical studs. These are then finished with hardwood cover trims and snap-in ‘invisible’ fixing inserts, thus retaining an elegant natural appearance. The hardwoods used are obtained from sustainable sources. Sound rated and 60 minute fire rated versions are available as are bespoke options.

 

Panels may be joined using either V-joints or ‘tape and fill’ which gives a smooth appearance and both timber and glass doors are offered.

 

Legno 75

 

Overall thickness: Nominal 1200mm modules on 50mm steel framework faced on both sides with a single layer of 12.5 mm thick panels. Nominally 75mm thick (95mm thick over the cover trims).

 

Glazing/Solid Options: Single offset glazing modules, centre glazed or double-glazed with various glazing methods and elevation options available. From 6 mm to 10 mm thick to comply with BS 6262 and appropriate fire requirements.

 

Panel joints: Expressed using half round or square-edged module trims with concealed fixing. Alternatively bevelled edged by means of wrapped bevelled edged panels with concealed retention.

 

Sound Rating: To BS 2750 Part 3 1980 and rated in accordance with BS 5281 Part 1 : 1984 up to 43 Rw (dB).

 

Timber Sections: All hardwoods are kiln-dried from sustainable sources complying with BS 1186 Part 1. Bespoke special designs or purpose made sections can be manufactured as requested.

 

Timber Finishes: Standard two coats of sealer plus wax finishing coat.

 

Internal framework: Rolled steel sections to BS 2994: 1976.

 

Panels: Standard gypsum compound to BS 1230 Part 1 to accept vinyl, paint or fabric decorative finishes. Alternative panels and finishes available.

 

Glass Doors: Glass doors are available to full height or with an overpanel in various widths manufactured from 10 mm or 12 mm glass, single or double leaf and single or double action.

 

Timber doors: Standard timber doors are 44 mm and are either 2040mm high x 826mm wide or 1981mm high x 838mm wide or full height. Other options are also available.

 

Door frames: Door frames are made of timber and will accept as standard 44 mm doors. Special designs or purpose made sections can be manufactured as requested.

 

Skirtings: Timber to match.

 

Privacy: Integral or free-hanging 15 mm or 25 mm venetian, roller or 89 mm or 127 mm louvers (manual or electronic mechanism).

 

Fire rating: to BS 476. Part 22 1987 (clause 8) solid up to 30 minutes insulation and integrity. Glazing up to 30 minutes integrity only. Timber door sets up to 30 minutes integrity only. Flame spread dependant on surface finish.

 

Legno 100

 

Overall thickness: Nominal 1200mm modules on 50mm steel framework faced on both sides with a double layer of 12.5 mm thick panels. Nominally 100mm thick (125mm thick over the cover trims).

 

Glazing/Solid Options: Single offset glazing modules, centre glazed or double-glazed with various glazing methods and elevation options available. From 6 mm to 10 mm thick to comply with BS 6262 and appropriate fire requirements.

 

Panel joints: Expressed using half round or square-edged module trims with concealed fixing. Alternatively bevelled edged by means of wrapped bevelled edged panels with concealed retention.

 

Sound Rating: To BS 2750 Part 3 1980 and rated in accordance with BS 5281 Part 1 : 1984 up to 43 Rw (dB).

 

Timber Sections: All hardwoods are kiln-dried from sustainable sources complying with BS 1186 Part 1. Bespoke special designs or purpose made sections can be manufactured as requested.

 

Timber Finishes: Standard two coats of sealer plus wax finishing coat.

 

Internal framework: Rolled steel sections to BS 2994: 1976.

 

Panels: Standard gypsum compound to BS 1230 Part 1 to accept vinyl, paint or fabric decorative finishes. Alternative panels and finishes available.

 

Glass Doors: Glass doors are available to full height or with an overpanel in various widths manufactured from 10 mm or 12 mm glass, single or double leaf and single or double action.

 

Timber doors: Standard timber doors are 54 mm and are either 2040mm high x 826mm wide or 1981mm high x 838mm wide or full height. Other options are also available.

 

Door frames: Door frames are made of timber and will accept as standard 54 mm doors. Special designs or purpose made sections can be manufactured as requested.

 

Skirtings: Timber to match.

 

Privacy: Integral or free-hanging 15 mm or 25 mm venetian, roller or 89 mm or 127 mm louvers (manual or electronic mechanism).

 

Fire rating: to BS 476. Part 22 1987 (clause 8) solid up to 60 minutes insulation and integrity. Glazing up to 60 minutes integrity only. Timber door sets up to 60 minutes integrity only. Flame spread dependant on surface finish.